Update README.md

README.md

@@ -5,6 +5,7 @@
 <p float="left">
 <img src="https://github.com/cecio/USBvalve/blob/main/pictures/versions.png" alt="The two models" width="30%" height="30%" />
 <img src="https://github.com/cecio/USBvalve/blob/main/pictures/USBvalve_PIWATCH.png" alt="The Watch" width="26%" height="26%" />
+<img src="https://github.com/cecio/USBvalve/blob/main/pictures/version1_2.png" alt="1.2" width="26%" height="26%" />
 </p>
 
 I'm sure that, like me, you were asked to put your USB drive in an *unknown* device...and then the doubt: 
@@ -170,8 +171,8 @@ I grouped most of the variables you may want to modify in this section ([see Doc
 
 Obviously you can also build your own firmware. To build the *standard* one I used:
 
-- Arduino IDE `2.3.1`
-- `Adafruit TinyUSB Library` version `3.0.0`, `Pico-PIO-USB` version `0.5.2`, Board `Raspberry Pi RP2040 (3.7.2)` setting Tools=>CPU Speed at `120MHz` and Tools=>USB Stack to `Adafruit TinyUSB`
+- Arduino IDE `2.3.2`
+- `Adafruit TinyUSB Library` version `3.1.1`, `Pico-PIO-USB` version `0.5.2`, Board `Raspberry Pi RP2040 (3.7.2)` setting Tools=>CPU Speed at `120MHz` and Tools=>USB Stack to `Adafruit TinyUSB`
 - `ssd1306` OLED library version `1.8.3`
 
 If you want to re-create a new fake filesystem, you may want to have a look to the `utils` folder, where I placed some utilities to build a new one.
@@ -190,3 +191,7 @@ The firmware will be placed with extension `uf2` in folder `USBvalve_out`.
 ### Contribute
 
 If you have ideas or improvements in your mind, I encourage you to open an issue so that we can improve the project together! Thanks!
+
+### Support
+
+If you have question or need support you can open an `Issue` here or reach me out on Twitter/X [@red5heep](https://twitter.com/red5heep)

USBvalve/USBvalve.ino

@@ -109,7 +109,7 @@ bool activeState = false;
 //
 // USBvalve globals
 //
-#define VERSION "USBvalve - 0.15.1"
+#define VERSION "USBvalve - 0.16.0"
 boolean readme = false;
 boolean autorun = false;
 boolean written = false;
@@ -244,7 +244,7 @@ void setup() {
 
 // Core 1 Setup: will be used for the USB host functions for BADUSB detector
 void setup1() {
-  // Set a custom clock (multiple of 12Mhz) to achieve maximum compatibility
+  // Set a custom clock (multiple of 12Mhz) to achieve maximum compatibility for HID
   set_sys_clock_khz(144000, true);
 
   pio_usb_configuration_t pio_cfg = PIO_USB_DEFAULT_CONFIG;
@@ -666,3 +666,31 @@ void cursor_movement(int8_t x, int8_t y, int8_t wheel) {
 }
 
 // END of BADUSB detector section
+
+//
+// OTHER Host devices detection section
+//
+
+// Invoked when a device with MassStorage interface is mounted
+void tuh_msc_mount_cb(uint8_t dev_addr) {
+  printout("\n[++] Mass Device");
+  SerialTinyUSB.printf("Mass Device attached, address = %d\r\n", dev_addr);
+}
+
+// Invoked when a device with MassStorage interface is unmounted
+void tuh_msc_umount_cb(uint8_t dev_addr) {
+  SerialTinyUSB.printf("Mass Device unmounted, address = %d\r\n", dev_addr);
+}
+
+// Invoked when a device with CDC (Communication Device Class) interface is mounted
+void tuh_cdc_mount_cb(uint8_t idx) {
+  printout("\n[++] CDC Device");
+  SerialTinyUSB.printf("CDC Device attached, idx = %d\r\n", idx);
+}
+
+// Invoked when a device with CDC (Communication Device Class) interface is unmounted
+void tuh_cdc_umount_cb(uint8_t idx) {
+  SerialTinyUSB.printf("CDC Device unmounted, idx = %d\r\n", idx);
+}
+
+// END of OTHER Host devices detector section